Twenty Five Boating Chores to do before next season arrives in the San Juan Islands

             Some chores are critical and some don't apply to all of us, but everyone has boating and sailing things to do before getting underway.     

         This website is supposed to be about  sailing and boating in the San Juans, so if I am stepping out of line here -- be sure to quit reading.

           For me and probably most of us, I pretty much quit boating during the winter months but I do go out a little and still must take care of routine chores.  I procrastinate more than I should and sometimes I win, but more often my procrastination causes me more problems and to spend more money.

         Recently I've done a few very important chores, and some busy work which is more fun, and I'll list off a few right now. Maybe a few readers will be reminded of something they forgot to take care of last season.

The numbers and order mean nothing but I think it looks cool to make lists.

1.  I just pulled completely apart my  trailers four wheels and bearings. Oh gawd what a greasy mess. I went through one and a half  rolls of paper towels.  One wheel had runny grease, so runny it ran out like heavy oil and it was lighter colored than the grease in the other wheels.  But it was full and showed no signs of not doing its job. I figure water must have gotten in and mixed with the grease, but I have seen frothy water contaminated grease and this didn't look like what I've seen. I cleaned it all up inspected the seal lip and repacked everything. All the brakes were totally covered and saturated with grease and brake lining debris making a black mess, which explains why the brakes never work as good as my other trailers. I have made a mental note to replace all backing plates and brake components next time. (more procrastination) Honestly now, they still work good enough, I hope. I ended up repacking two wheels completely, one I looked at and put back together and one just got some grease added . I feel confident about my bearings now and don't have any worries for upcoming road travel.
2. I cut off the dinghy line that was too long and got caught in the prop last summer.
3. My last window leak has succumbed to Captain Tolley's Creeping Crack Cure because I got smart enough to apply it to both the inside and outside surfaces.
4. I have refilled about a dozen non refillable propane tanks. (fyi - my cost is about $1 per canister and I do not in any way suggest that anyone refill non refillable bottles)
5. I built a kicker motor adapter bracket so my 5hp Honda sits sideways and now clears the water as well as the dinghy's gelcoat while being carried on the mother ship.
6. I have added rigid SS standoffs after dropping the dinghy and rope burning my hands.
7. I have built two kerosene lamp holders so I can hang my lamps from the ceiling hooks.
8. A few months ago I touched up the bottom paint.
9. I added a vinyl drip rail gutter to the cabin roofs, a project that I worried about being able to apply straight but it turned out to be really easy and looks great.
10. I added a site tube to my water tank, so I can see the water level without putting a flashlight behind the tank and then guessing.
11. I haven't yet, but I do have the yellow pad I'm going to use to create a ships manifest list of everything stored on board including where each item is stored. Then I plan to transcribe the list and print out a good looking copy to be kept in my ship's log book.  Yes it is true, I can't remember where I put things.
12. I built a new front hatch using half inch Lexan and something that looks a lot like oak.
13. I have taken satellite screenshots and loaded my laptop with all the likely ports of call for my up coming Sunshine Coast cruise to Princess Louisa Inlet in the middle of June.
14. I bought two used Canadian charts, since my chart plotter doesn't have anything north of Vancouver.
15. I changed my motor oil last fall so it would sit with mostly fresh oil through the winter.
16. I have upgraded my bicycle to  tires full of that anti puncture anti leak glop stuff.
17. I already wrote about fixing the stoves oil drip valve adjustment so it actually is adjustable.  I was forced to do that from prior procrastination caused problems, but I still want credit.
18. I got on my stomach in a half open hatch, and with a mirror and flashlight checked the water level in my batteries.
19. I traced my windlass wiring and discovered an off/on switch I had forgot about. Now my windlass works again after hand hauling chain last year.
20. I added a mid-ship cleat on the starboard side, the PO must have always tied to port or didn't see the need for proper spring lines.
21. I installed some good looking golden maple click-lock flooring that closely matches the old teak, at least in color.
22. I accidentally broke off my am/fm radio antenna, but it still works pretty good so I just cleaned up the fiberglass shreds and pushed a rubber cap over the jagged end.  
23. I replaced all the uv damaged tie cords on my cabin top kayak rack.
24. I have built and installed all the components to convert my Livingston dinghy to sail, some fine tuning is still needed but I have had several successful (and fun) sea trials. I may just procrastinate and go with it as is, I can finish up the little stuff later.
25. I just started what was to be a simple port side light relighting. It seems banging on the light wouldn't cause it to work anymore. When I turned the brass screw heads, both stripped so I drilled them out. After pulling off the lens I grabbed the drilled studs with vise grips and broke them off.  Now there is no way to reattach the lens and I have not even gotten to why the light doesn't light up. More on this later, I'm on way to Ace to find 2.5" x #6 brass screws, I know, "fat chance."

Still to come this year I hope:

1. Fix the bimini tie downs, not done yet
2. Drill or make a drain hole for the front hatch (limber holes were forgot, don't ask)
3. Fill flat fenders with more air and look for leaks.
4. Find plates that fit in sink or cut a quarter inch off the pretty fishy painted ones my wife likes.
5. ???

I hope your commissioning chores are as fulfilling as mine are. Lets see wax or polish, what's the difference again?

What Is The Perfect San Juan Islands Boat - What Equipment is Mandatory

    I  was talking to someone the other day that was earnestly looking for a boat for a passage to Hawaii. He remarked that the vessel he was considering did not have an anchor windlass and he sure would like one.  That comment got me thinking about how often one needs to anchor on the way to Hawaii, and then I thought what else do we think we need but really don’t need at all. 

                In the San Juans we anchor all the time, plus an anchor can be a last chance emergency brake when the motor conks out.  On the way to Hawaii I just don’t see any use for an anchor or windlass, and I doubt motoring very far is in the cards either, so a dependable motor ranks somewhere behind standing rigging because if the mast folds up and goes over the side in the San Juans it’s a big deal and probably will require motoring  back to home base.  If the same thing happens a thousand miles from shore its more than a big deal, it could mean a rescue, so having stout rigging is a must going to Hawaii, but not in the San Juans. How about tanks, do we need a holding tank in the San Juan’s, the answer is no, but they are very handy if you do not want to be tied to resorts and shore side facilities. On the way to Hawaii, I think a holding tank won’t be missed.  Fresh water tank, yes. I think you need one going to Hawaii, but in the San Juans, no, you can make it from place to place with a sports bottle in your pocket.  How about a compass, I think yes in both scenario’s.   Radar is a resounding not needed in either case but a gps and radio I think you need, and since they are relatively cheap and portable there is no real good reason not to have them with you. A chart plotter is not needed but a paper chart is needed whether going to Hawaii or hanging around the San Juans.

How about a refrigerator, nope you can get by without one and save a lot of juice at the same time. 

Did I leave out anything big?  Yes! No!  Of course you need basics like a bilge pump or a bucket, but let’s face it a dinghy is handy but not required, so is a new suit of sails.  I think a good argument can be made for having an emergency life raft out in the middle of the ocean, but not so good an argument in the San Juans.

The purpose for this line of thought as I said in the beginning was to think some about

what gear is really needed on my boat, or on the boat  being considered.

Click below to read more

Practicing What I Preach

          One way to plan a cruise to the San Juan's!

     Many times on this site I have suggested that the most important planning thing to do is set a date, and the rest of the cruise will come together, that philosophy has not changed.  But that doesn't mean you can ignore important details expecting them to magically fall in place.  Someone still has to grease the wheel bearings, apply for passports, order techie toys, mow the lawn.
     
     Just put a big X on the calendar and then sit back and let your cruise plan unfold (bad word choice, sounds too much like unravel) just sit back and let your plan develop.  In our case, with some prodding (one poke) from my oldest daughter, I agreed to go to Roche Harbor for the 4th of July.  No big X date on exact arrival but the 4th is the 4th, so I figured  we would arrive in the general area a few days earlier.

     Now, some months later,  the plan is starting to come together.  I have a day planned for bike riding on San Juan.  I have a  campfire night planned on shore at Jones for hot dogs.  I have a toss up day to get Ice Cream at Blakelys or Friday Harbor, and it looks like if I can make my Livingston Dinghy sail properly, I will have the day of the 4th to sail around Roche Harbor dodging anchor lines and other dinghies.  Yesterday another daughter announced she and her friends had camping reservations on San Juan Island, also over the 4th of July, and that I could give her, her friends and their bicycles a ride over to Lopez on the 2nd, and then they would ride the ferry back that evening.  The plan for Saturday after the 4th is still open, but I know it will fall in place just like always.

       So, we put the big X on the calendar, and the plan is evolving, I can't believe I used to actually stress over vacation details.  I wonder if I should enter the blind dinghy race the day of the 4th.  hmmm!



Just in case someone needs an exhausting check list to stress out over when making plans, take a look here.
Cruisers - Mother of all Packing lists!   <<< click there

       
   

A reminder for me again! Murphy's Law!

        My dinghy, just like many others is mounted on snap davits across the transom and stood on edge for travel.  This has been my preferred system for many boats and even more dinghies. To tilt and raise the dinghy up and out of the water I have two nylon lines attached to cleats on the far side.  I wrap one line around each wrist and then with a heave, I lean back and pull the dinghy up onto its side. Next with the dinghy balanced in a somewhat neutral position I carefully tie off both lines by wrapping around the stern rail and back to the dinghy cleat.  For lowering the dinghy I wrap the lines several times around the rail creating a friction brake, then effortlessly let out enough line to set her back in the water.

   So far so good, but here's the reminder part. Last week while lowering the dinghy, my cleated lines somehow became loose, I didn't see it in time and the dinghy fell without any braking wraps. I had one hand on a line but was unable to hold it, so it whistled through my grasp taking with it a bunch of my flesh leaving me with a painful rope burn.  To  add insult, after the dinghy fell I discovered my oars were about to slide out of their poorly knotted  lines as well. Some regulars may remember these are the same lines I managed to wrap around the prop at Jones Island last year.  I'll save the procrastination post for later.

     There are lessons and reminders here.

   

• Even though I think I tie great knots and cleat well, I failed.
• I should have a redundant tie off system.

     This experience got me thinking, what else is about to trip me up?

• loose bolt/nuts
• cotter pins not spread enough
• zincs, corroded fasteners
• belts, hoses, clamps, 
• electrical connections, battery condition/quality
• are my flares expired, where is my whistle?
• anchor shackle pin seizing wire
• fuel system, (this is a big potential problem area) fuel stabilizer 
• waste system (that reminds me, I think the vent is plugged)
• fresh water chlorination, (oh yeah, forgot that too)
• diesel exhaust smell in the clothes closet, still not addressed!
• hatch seal
• dock lines are still a mish mash of old ropes and  one fender is flat
• telescoping boat pole is jammed at five feet

I put this list together in a few minutes, so there is plenty I missed.

No preaching this time,  but I hope I got some of you thinking.

Understanding the Rule of Twelfths Formula for Tide Predictions in the San Juan Islands

Disclaimer #1 

I have read this little tool rule many times by different authors and each time have come away confused and surprised at how such a simple idea can come out so convoluted and nonsensical. I wrote my clearly understandable version below and tried it on Linda who knows and understands the rule only to hear  "Your writing is  confusing, why did you say tidal range?"

phooey

"The Rule of Twelfths"

      
 First, lets think in terms of where we will apply this tool.  For me it is when I need to anchor and I don’t know how far the tide is going to drop or rise.  Will my keel touch bottom in two hours, will the anchor drag while we sleep?  These important questions need answering before setting the hook.

       To employ the rule you must know some approximate facts first. #1, what is the tidal range in the area, ie. if the tide book states high tide is 8.5 feet and low tide is 1.5 feet, the total range the water rises or falls is 7 feet. As you know every day is different and varies by area so our first fact is just an approximation.  #2, we need to know what time high or low tide is forecast.  These two facts are all we need to know and we can arrive at the anchorage and make a good estimate of what to expect.

       Most areas have a six hour duration from low tide to high tide so we need to think in terms of six one hour segments. During the first hour the water rises or falls slowly. During the second hour the rise or fall picks up speed.  During the third and fourth hours, the water is moving at its fastest rate, and the fifth and sixth hours are slower and mirror hours one and two.  That’s the cycle that is repeated regardless of area or total range.  Slow at first, picking up speed, very fast, then slow down, and come to a stop, in six hours and then repeat.

       So now we have a six hour period broken into one hour segments, it’s time to assign a value to each hour and the following is the backbone of the Rule of Twelfths  123321, (each number represents one hour) yes they do add up to twelve. In the first hour after slack water, the water will move 1/12 of the range, in the second hour the water will move 2/12 of the range, or double the first. In the third hour the water moves 3/12 of the entire range. So this means that three hours after slack, or three hours  before the next slack, the water has moved a total of 6/12 or halfway through its range.  We already know that at the halfway point the tide is moving at its fastest and is halfway in or out, so no surprise there.  When we arrive at an anchorage exactly halfway between high and low tide, all we need to know is the total range and we can easily determine how much more or less to expect.  Where this tool helps most is during the second hour or fifth hour, referring back to our rule of 123321 we see the fifth hour totals 10/12, and the second hour total 3/12 of the range. By reducing fractions we easily understand that in the fifth hour the tide has moved 5/6 of the range and only has about 1-2 feet still to go. In the second hour the tide has only moved  1/4 the range and so still has about 4-5 feet to move.

       Armed with this knowledge you can easily determine how much the water will rise or fall and anchor where the depth is best for your boat.  So remember 123321,  know the tidal range in your area, and what time high or low tide is forecast. The rest is just fractions.

Disclaimer #2

       As a practical matter, I don't park the boat with just a foot of clearance under my goodies unless I have a good reason, such as I'm at a dock at low tide and I know whats coming.  Swinging at anchor with only a foot to spare is asking for it in some locations.  For you naysayers consider what happens to your boat when a big swell comes your way, that's right it is followed by a trough.  Well not only does a one foot trough take away your clearance, but it slams you violently on the bottom to tell you so.

       So, even though the Rule of Twelfths is a fun exercise, and I recommend everyone understand the ups and downs of tides, (ha) I still look for lots of depth at low tide, set my anchors very well, and sleep even better.

Here is a link to the NOAA tide tables  > NOAA tide tables

My shore power cord got so hot the plastic plug melted and had to be pried off the connection

Where have we been for the last sixty days?      

       I have felt bad for not posting recently, but not anymore.  Just as I sat down it occurred to me that many of us are in the same situation. Winter projects, holidays etc. Now that I have time to write, some of you may have time to stop by, and the fact that two months has gone by is not an issue.

         One of my projects was to keep my boat from freezing solid and being damaged. So far so good.  We went for a Thanksgiving weekend cruise in freezing weather, which was my last post about the stove huffing and puffing soot all over the place. You know soot becomes snoot when it gets wet or rubbed or wiped or touched. It also seems to permanently sink into oxidized fiberglass.  Bad news all around, snoot is. The good news is that it cleans off  painted surfaces really nice and almost cleans off waxed surfaces.

        On New Years we went for another cold weather outing and the oil stove worked flawlessly now that I know to pay better attention to the burner.

      Now about the hot wire,  and warning  for all of us that know better.  My 30 amp power plug got so hot that it partially melted the plastic and I had a really hard time removing the plug from the receptacle on the boat.  

        The heat was caused by two things #1 the plug terminals must not have  made a good connection so I'm not getting 30 amps, instead I'm getting heat.   #2 the electric heater and battery charger in the boat probably combine for too much power draw, and with the cold weather I'm lucky I caught it before - poof - a different kind of snoot appeared where the boat is/was. My advice to myself is to check both ends of every cable connection for heat. What worry's me are the buried connections I can't get to.

Here's proof it can happen  - Clickety click   >>  >>  fire damage

This picture shows smoke damage.  My first thought was that I could simply clean  the surfaces.
Think again skipper -- some surfaces clean really well and some become etched.  Smoke is extremely corrosive, and in a closed boat fire, flames may not be present but the smoldering fire pressurizes and forces smoke into and behind every nook and cranny.  Nothing escapes, not the field glasses, not the radio,  not the switch  panel or any electrical terminals .

      Within six months of this fire - all electrical switches, contacts failed.  Wires survived, but all had to be re-cut and new terminals crimped.  (The adjuster totaled the boat)

The cause of the fire was an overheated extension cord.  You can see the orange cord in the picture  So regrettable and preventable.